Fatigue behavior of AW7075 aluminum alloy in ultra-high cycle fatigue region
Advanced electron microscopy methods were used with the aim to explain the differences in the response of strengthened AW 7075 – T6511 aluminum alloy to fatigue loading at 5 Hz and 20 kHz. The shift of the S–N curve to higher number of cycles to fracture for the specimens tested at high frequency wa...
Uložené v:
| Vydané v: | Materials science & engineering. A, Structural materials : properties, microstructure and processing Ročník 774; s. 138922 |
|---|---|
| Hlavní autori: | , , , , |
| Médium: | Journal Article |
| Jazyk: | English |
| Vydavateľské údaje: |
Lausanne
Elsevier B.V
13.02.2020
Elsevier BV |
| Predmet: | |
| ISSN: | 0921-5093, 1873-4936 |
| On-line prístup: | Získať plný text |
| Tagy: |
Pridať tag
Žiadne tagy, Buďte prvý, kto otaguje tento záznam!
|
| Abstract | Advanced electron microscopy methods were used with the aim to explain the differences in the response of strengthened AW 7075 – T6511 aluminum alloy to fatigue loading at 5 Hz and 20 kHz. The shift of the S–N curve to higher number of cycles to fracture for the specimens tested at high frequency was experimentally determined. This effect is not connected with a change of the fatigue crack initiation mechanism and site from the surface to material interior. The absence of slip markings and cracking of primary intermetallic particles on the surface of cycled specimens were characteristic features. A difference in the dislocation density and dislocation arrangement in the vicinity of the fatigue crack initiation sites was shown to be the only observable effect. However, consistent with the strengthened structure of the alloy, no specific dislocation structure due to the cyclic loading was observed, regardless of the loading frequency and stress amplitude. |
|---|---|
| AbstractList | Advanced electron microscopy methods were used with the aim to explain the differences in the response of strengthened AW 7075 – T6511 aluminum alloy to fatigue loading at 5 Hz and 20 kHz. The shift of the S–N curve to higher number of cycles to fracture for the specimens tested at high frequency was experimentally determined. This effect is not connected with a change of the fatigue crack initiation mechanism and site from the surface to material interior. The absence of slip markings and cracking of primary intermetallic particles on the surface of cycled specimens were characteristic features. A difference in the dislocation density and dislocation arrangement in the vicinity of the fatigue crack initiation sites was shown to be the only observable effect. However, consistent with the strengthened structure of the alloy, no specific dislocation structure due to the cyclic loading was observed, regardless of the loading frequency and stress amplitude. Advanced electron microscopy methods were used with the aim to explain the differences in the response of strengthened AW 7075 – T6511 aluminum alloy to fatigue loading at 5 Hz and 20 kHz. The shift of the S–N curve to higher number of cycles to fracture for the specimens tested at high frequency was experimentally determined. This effect is not connected with a change of the fatigue crack initiation mechanism and site from the surface to material interior. The absence of slip markings and cracking of primary intermetallic particles on the surface of cycled specimens were characteristic features. A difference in the dislocation density and dislocation arrangement in the vicinity of the fatigue crack initiation sites was shown to be the only observable effect. However, consistent with the strengthened structure of the alloy, no specific dislocation structure due to the cyclic loading was observed, regardless of the loading frequency and stress amplitude. |
| ArticleNumber | 138922 |
| Author | Horník, V. Trško, L. Kuběna, I. Kunz, L. Fintová, S. |
| Author_xml | – sequence: 1 givenname: S. surname: Fintová fullname: Fintová, S. email: fintova@ipm.cz organization: Institute of Physics of Materials, The Czech Academy of Sciences, Žižkova 22, 616 62, Brno, Czech Republic – sequence: 2 givenname: I. surname: Kuběna fullname: Kuběna, I. organization: Institute of Physics of Materials, The Czech Academy of Sciences, Žižkova 22, 616 62, Brno, Czech Republic – sequence: 3 givenname: L. surname: Trško fullname: Trško, L. organization: Research Centre of the University of Žilina, University of Žilina, Univerzitná 8215/1, 010 26, Žilina, Slovakia – sequence: 4 givenname: V. surname: Horník fullname: Horník, V. organization: Institute of Physics of Materials, The Czech Academy of Sciences, Žižkova 22, 616 62, Brno, Czech Republic – sequence: 5 givenname: L. surname: Kunz fullname: Kunz, L. organization: Institute of Physics of Materials, The Czech Academy of Sciences, Žižkova 22, 616 62, Brno, Czech Republic |
| BookMark | eNp9kD1rwzAQhkVJoUnaP9DJ0NmpPiJLgi4hNG0h0KWlo5DlcyJjW6lsB_Lvq-BMHTLdcdxzx_vM0KT1LSD0SPCCYJI9V4umA7OgmMYBk4rSGzQlUrB0qVg2QVOsKEk5VuwOzbquwhiTJeZTtN2Y3u0GSHLYm6PzIfFlsvoRWPDE1EPj2qGJTe1PiWuToe6DSfdut0_sydaQlBc6wM759h7dlqbu4OFS5-h78_q1fk-3n28f69U2tYzKPjU5prkBxgtespLmaskgk6rIpCmA5BQwlQqsYJkwnGBMlclAcKak5VQCY3P0NN49BP87QNfryg-hjS815ULFZFLQuEXHLRt81wUo9SG4xoSTJlifrelKn63pszU9WouQ_AdZ18eQvo3JXX0dfRlRiNGPDoLurIPWQuEC2F4X3l3D_wBhQ4iJ |
| CitedBy_id | crossref_primary_10_1038_s41524_021_00506_8 crossref_primary_10_3390_ma18050943 crossref_primary_10_1016_j_surfcoat_2020_125698 crossref_primary_10_1016_j_ijfatigue_2020_105865 crossref_primary_10_1061_JMCEE7_MTENG_17933 crossref_primary_10_1016_j_engfailanal_2020_104830 crossref_primary_10_1016_j_msea_2021_141917 crossref_primary_10_1016_j_powtec_2025_121162 crossref_primary_10_1016_j_engfracmech_2021_107718 crossref_primary_10_1016_j_tafmec_2024_104590 crossref_primary_10_1016_j_conbuildmat_2023_134520 crossref_primary_10_3390_ma14102565 crossref_primary_10_1007_s40192_021_00219_2 crossref_primary_10_1016_j_ijfatigue_2022_107295 crossref_primary_10_1007_s40192_024_00343_9 |
| Cites_doi | 10.1016/j.proeng.2014.06.257 10.1016/j.ijfatigue.2013.10.016 10.1016/0001-6160(70)90043-X 10.1016/j.engfailanal.2013.03.020 10.1007/s00170-017-0776-1 10.1080/14786437608223793 10.1088/1742-6596/896/1/012004 10.1007/BF00041859 10.1007/BF02642389 10.1016/j.ijfatigue.2009.06.003 10.1016/S0142-1123(03)00147-6 10.1016/S0142-1123(01)00123-2 10.3390/met8020111 10.3390/met6040079 10.1016/j.ijfatigue.2005.05.018 10.1016/j.proeng.2013.03.307 10.1016/j.msea.2006.07.168 10.1016/0956-7151(95)90165-5 10.1007/BF02667404 10.1016/0921-5093(89)90859-9 10.1016/S0921-5093(00)01978-X 10.1016/j.msea.2013.12.005 10.1080/01418618108239541 10.1016/j.surfcoat.2008.06.049 10.1007/BF00576770 10.1088/0965-0393/16/6/065007 |
| ContentType | Journal Article |
| Copyright | 2020 Elsevier B.V. Copyright Elsevier BV Feb 13, 2020 |
| Copyright_xml | – notice: 2020 Elsevier B.V. – notice: Copyright Elsevier BV Feb 13, 2020 |
| DBID | AAYXX CITATION 7SR 8BQ 8FD JG9 |
| DOI | 10.1016/j.msea.2020.138922 |
| DatabaseName | CrossRef Engineered Materials Abstracts METADEX Technology Research Database Materials Research Database |
| DatabaseTitle | CrossRef Materials Research Database Engineered Materials Abstracts Technology Research Database METADEX |
| DatabaseTitleList | Materials Research Database |
| DeliveryMethod | fulltext_linktorsrc |
| Discipline | Engineering |
| EISSN | 1873-4936 |
| ExternalDocumentID | 10_1016_j_msea_2020_138922 S0921509320300149 |
| GroupedDBID | --K --M -~X .~1 0R~ 1B1 1~. 1~5 4.4 457 4G. 5GY 5VS 7-5 71M 8P~ 9JN AABNK AABXZ AACTN AAEDT AAEDW AAEPC AAIAV AAIKJ AAKOC AALRI AAOAW AAQFI AAXUO ABFNM ABMAC ABXRA ABYKQ ACDAQ ACGFS ACIWK ACRLP ADBBV ADEZE AEBSH AEKER AEZYN AFKWA AFRZQ AFTJW AGHFR AGUBO AGYEJ AHHHB AIEXJ AIKHN AITUG AJOXV ALMA_UNASSIGNED_HOLDINGS AMFUW AMRAJ AXJTR BKOJK BLXMC CS3 EBS EFJIC EFLBG EO8 EO9 EP2 EP3 F5P FDB FIRID FNPLU FYGXN G-Q GBLVA IHE J1W KOM M24 M41 MAGPM MO0 N9A O-L O9- OAUVE OZT P-8 P-9 PC. Q38 RNS ROL RPZ SDF SDG SDP SES SMS SPC SPCBC SSM SSZ T5K ~02 ~G- 29M 6TJ 8WZ 9DU A6W AAQXK AATTM AAXKI AAYWO AAYXX ABDPE ABJNI ABWVN ABXDB ACLOT ACNNM ACRPL ADMUD ADNMO AEIPS AFJKZ AGQPQ AIIUN ANKPU APXCP ASPBG AVWKF AZFZN CITATION EFKBS EJD FEDTE FGOYB G-2 HVGLF HZ~ R2- SEW WUQ ~HD 7SR 8BQ 8FD AFXIZ AGCQF AGRNS BNPGV JG9 SSH |
| ID | FETCH-LOGICAL-c328t-ab02bae35d5f3f2b943e689d68ade1b2e0289ec7367a510029a6e75398c528e33 |
| ISICitedReferencesCount | 19 |
| ISICitedReferencesURI | http://www.webofscience.com/api/gateway?GWVersion=2&SrcApp=Summon&SrcAuth=ProQuest&DestLinkType=CitingArticles&DestApp=WOS_CPL&KeyUT=000514747200013&url=https%3A%2F%2Fcvtisr.summon.serialssolutions.com%2F%23%21%2Fsearch%3Fho%3Df%26include.ft.matches%3Dt%26l%3Dnull%26q%3D |
| ISSN | 0921-5093 |
| IngestDate | Fri Jul 25 05:13:16 EDT 2025 Tue Nov 18 19:48:06 EST 2025 Sat Nov 29 07:14:23 EST 2025 Fri Feb 23 02:49:23 EST 2024 |
| IsPeerReviewed | true |
| IsScholarly | true |
| Keywords | Fatigue Ultra-high cycle fatigue AW7075 Fatigue damage Fatigue crack initiation |
| Language | English |
| LinkModel | OpenURL |
| MergedId | FETCHMERGED-LOGICAL-c328t-ab02bae35d5f3f2b943e689d68ade1b2e0289ec7367a510029a6e75398c528e33 |
| Notes | ObjectType-Article-1 SourceType-Scholarly Journals-1 ObjectType-Feature-2 content type line 14 |
| PQID | 2579140872 |
| PQPubID | 2045432 |
| ParticipantIDs | proquest_journals_2579140872 crossref_primary_10_1016_j_msea_2020_138922 crossref_citationtrail_10_1016_j_msea_2020_138922 elsevier_sciencedirect_doi_10_1016_j_msea_2020_138922 |
| PublicationCentury | 2000 |
| PublicationDate | 2020-02-13 |
| PublicationDateYYYYMMDD | 2020-02-13 |
| PublicationDate_xml | – month: 02 year: 2020 text: 2020-02-13 day: 13 |
| PublicationDecade | 2020 |
| PublicationPlace | Lausanne |
| PublicationPlace_xml | – name: Lausanne |
| PublicationTitle | Materials science & engineering. A, Structural materials : properties, microstructure and processing |
| PublicationYear | 2020 |
| Publisher | Elsevier B.V Elsevier BV |
| Publisher_xml | – name: Elsevier B.V – name: Elsevier BV |
| References | Payne, Welsh, Christ, Nardiello, Papazian (bib22) 2010; 32 Papazian (bib18) 1982; 13 Marines, Bin, Bathias (bib15) 2003; 25 Messerschmidt (bib28) 2010 Genel (bib32) 2013; 32 Lütjering, Döker, Munz (bib26) 1973; vol. 1 Zhai, Martin, Briggs (bib6) 1995; 43 Essmann, Gösele, Mughrabi (bib10) 1981; 44 Polák, Man (bib8) 2014; 596 Bathias, Drouillac, Le François (bib14) 2001; 23 Cirik, Genel (bib31) 2008; 202 Adler, DeIasi (bib17) 1977; 8 Polák, Man (bib9) 2014; 65 Hu, Wang (bib1) 2016; 6 Nicholas (bib3) 2006 Behrens, Nürnberger, Bonk, Hübner, Behrens, Vogt (bib19) 2017; 896 Mughrabi (bib25) 2013; 55 Trško, Fintová, Nový, Bokůvka, Jambor, Pastorek, Florková, Oravcová (bib34) 2018; 8 Polák (bib7) 1991 Mughrabi (bib2) 2006; 28 Wang, Nikitin, Shanyavskiy, Bathias (bib4) 2012 Antonopoulos, Brown, Winter (bib5) 1976; 34 Trško, Guagliano, Bokůvka, Nový (bib33) 2014; 74 Lin, Lin (bib11) 1979 Lütjering, Albrecht, Sauer, Krull (bib20) 2007; 468–470 Anderson, Hirth, Lothe (bib13) 2017 Bozek, Hochhalter, Veilleux, Liu, Heber, Sintay, Rollett, Littlewood, Maniatty, Weiland, Christ, Payne, Welsh, Harlow, Wawrzynek, Ingraffea (bib24) 2008; 16 Hadzima, Nový, Trško, Pastorek, Jambor, Fintová (bib30) 2017; 93 Lütjering, Weissmann (bib27) 1970; 18 Papakyriacou, Mayer, Pypen, Plenk, Stanzl-Tschegg (bib12) 2001; 308 Park, Ardell (bib16) 1989; 114 Srivatsan, Lavernia (bib21) 1991; 26 Bowles, Schijve (bib23) 1973; 9 Papazian (10.1016/j.msea.2020.138922_bib18) 1982; 13 Lütjering (10.1016/j.msea.2020.138922_bib26) 1973; vol. 1 Polák (10.1016/j.msea.2020.138922_bib7) 1991 Anderson (10.1016/j.msea.2020.138922_bib13) 2017 Trško (10.1016/j.msea.2020.138922_bib34) 2018; 8 Bozek (10.1016/j.msea.2020.138922_bib24) 2008; 16 Wang (10.1016/j.msea.2020.138922_bib4) 2012 Antonopoulos (10.1016/j.msea.2020.138922_bib5) 1976; 34 Hadzima (10.1016/j.msea.2020.138922_bib30) 2017; 93 Polák (10.1016/j.msea.2020.138922_bib9) 2014; 65 Papakyriacou (10.1016/j.msea.2020.138922_bib12) 2001; 308 Essmann (10.1016/j.msea.2020.138922_bib10) 1981; 44 Bowles (10.1016/j.msea.2020.138922_bib23) 1973; 9 Payne (10.1016/j.msea.2020.138922_bib22) 2010; 32 Mughrabi (10.1016/j.msea.2020.138922_bib25) 2013; 55 Bathias (10.1016/j.msea.2020.138922_bib14) 2001; 23 Srivatsan (10.1016/j.msea.2020.138922_bib21) 1991; 26 Adler (10.1016/j.msea.2020.138922_bib17) 1977; 8 Zhai (10.1016/j.msea.2020.138922_bib6) 1995; 43 Lin (10.1016/j.msea.2020.138922_bib11) 1979 Cirik (10.1016/j.msea.2020.138922_bib31) 2008; 202 Polák (10.1016/j.msea.2020.138922_bib8) 2014; 596 Marines (10.1016/j.msea.2020.138922_bib15) 2003; 25 Trško (10.1016/j.msea.2020.138922_bib33) 2014; 74 Behrens (10.1016/j.msea.2020.138922_bib19) 2017; 896 Mughrabi (10.1016/j.msea.2020.138922_bib2) 2006; 28 Lütjering (10.1016/j.msea.2020.138922_bib20) 2007; 468–470 Nicholas (10.1016/j.msea.2020.138922_bib3) 2006 Genel (10.1016/j.msea.2020.138922_bib32) 2013; 32 Hu (10.1016/j.msea.2020.138922_bib1) 2016; 6 Messerschmidt (10.1016/j.msea.2020.138922_bib28) 2010 Park (10.1016/j.msea.2020.138922_bib16) 1989; 114 Lütjering (10.1016/j.msea.2020.138922_bib27) 1970; 18 |
| References_xml | – start-page: 707 year: 1979 end-page: 728 ident: bib11 article-title: Micromechanics theory of fatigue crack initiation applied to time-dependent fatigue publication-title: Fatigue Mechanisms – volume: 25 start-page: 1101 year: 2003 end-page: 1107 ident: bib15 article-title: An understanding of very high cycle fatigue of metals publication-title: Int. J. Fatigue – volume: 896 year: 2017 ident: bib19 article-title: Influences on the formability and mechanical properties of 7000-aluminum alloys in hot and warm forming publication-title: J. Phys. Conf. Ser. – volume: 18 start-page: 785 year: 1970 end-page: 795 ident: bib27 article-title: Mechanical properties of age-hardened titanium-aluminum alloys publication-title: Acta Metall. – volume: 8 start-page: 1185 year: 1977 end-page: 1190 ident: bib17 article-title: Calorimetric studies of 7000 series aluminum alloys: II. Comparison of 7075, 7050 and RX720 alloys publication-title: Metall. Trans.A – volume: vol. 1 start-page: 427 year: 1973 end-page: 431 ident: bib26 article-title: Microstructure and fatigue behavior of Al-alloys publication-title: International Conference of the Strength of Metals and Alloys, in: Proceedings of the Third International Conference on the Strength of Metals and Alloys – volume: 26 start-page: 940 year: 1991 end-page: 950 ident: bib21 article-title: The presence and consequences of precipitatefree zones in an aluminium-copper-lithium alloy publication-title: J. Mater. Sci. – volume: 44 start-page: 405 year: 1981 end-page: 426 ident: bib10 article-title: A model of extrusions and intrusions in fatigued metals I. Point-defect production and the growth of extrusions publication-title: Philos. Mag. A – volume: 74 start-page: 246 year: 2014 end-page: 252 ident: bib33 article-title: Fatigue life of AW 7075 aluminium alloy after severe shot peening treatment with different intensities publication-title: Procedia Engineering – volume: 32 start-page: 248 year: 2013 end-page: 260 ident: bib32 article-title: Environmental effect on the fatigue performance of bare and oxide coated 7075-T6 alloy publication-title: Eng. Fail. Anal. – volume: 9 start-page: 171 year: 1973 end-page: 179 ident: bib23 article-title: The role of inclusions in fatigue crack initiation in an aluminum alloy publication-title: Int. J. Fract. – volume: 65 start-page: 18 year: 2014 end-page: 27 ident: bib9 article-title: Fatigue crack initiation – the role of point defects publication-title: Int. J. Fatigue – year: 1991 ident: bib7 article-title: Cyclic Plasticity and Low Cycle Fatigue Life of Metals – volume: 596 start-page: 15 year: 2014 end-page: 24 ident: bib8 article-title: Mechanisms of extrusion and intrusion formation in fatigued crystalline materials publication-title: Mater. Sci. Eng. A – volume: 93 start-page: 3315 year: 2017 end-page: 3323 ident: bib30 article-title: Shot peening as a pre-treatment to anodic oxidation coating process of AW 6082 aluminum for fatigue life improvement publication-title: Int. J. Adv. Manuf. Technol. – year: 2006 ident: bib3 article-title: High Cycle Fatigue: A Mechanics of Materials Perspective – volume: 13 start-page: 761 year: 1982 end-page: 769 ident: bib18 article-title: Calorimetric studies of precipitation and dissolution kinetics in aluminum alloys 2219 and 7075 publication-title: Metall. Trans.A – start-page: 367 year: 2012 end-page: 374 ident: bib4 article-title: An understanding of crack growth in VHCF from an internal inclusion in high strength steel publication-title: Crack Paths, Gruppo Italiano Frattura – volume: 16 year: 2008 ident: bib24 article-title: A geometric approach to modeling microstructurally small fatigue crack formation: I. Probabilistic simulation of constituent particle cracking in AA 7075-T651 publication-title: Model. Simul. Mater. Sci. Eng. – volume: 43 start-page: 3813 year: 1995 end-page: 3825 ident: bib6 article-title: Fatigue damage in aluminium single crystals. I. On the surface containing the slip Burgers vector publication-title: Acta Metall. Mater. – year: 2017 ident: bib13 article-title: Theory of Dislocations – volume: 468–470 start-page: 201 year: 2007 end-page: 209 ident: bib20 article-title: The influence of soft, precipitate-free zones at grain boundaries in Ti and Al alloys on their fatigue and fracture behavior publication-title: Mater. Sci. Eng. A – volume: 202 start-page: 5190 year: 2008 end-page: 5201 ident: bib31 article-title: Effect of anodic oxidation on fatigue performance of 7075-T6 alloy publication-title: Surf. Coat. Technol. – volume: 28 start-page: 1501 year: 2006 end-page: 1508 ident: bib2 article-title: Specific features and mechanisms of fatigue in the ultrahigh-cycle regime publication-title: Int. J. Fatigue – year: 2010 ident: bib28 article-title: Dislocation Dynamics during Plastic Deformation – volume: 114 start-page: 197 year: 1989 end-page: 203 ident: bib16 article-title: Correlation between microstructure and calorimetric behavior of aluminum alloy 7075 and AlZnMg alloys in various tempers publication-title: Mater. Sci. Eng. A – volume: 308 start-page: 143 year: 2001 end-page: 152 ident: bib12 article-title: Influence of loading frequency on high cycle fatigue properties of b.c.c. and h.c.p. metals publication-title: Mater. Sci. Eng. A – volume: 55 start-page: 636 year: 2013 end-page: 644 ident: bib25 article-title: Damage mechanisms and fatigue lives: from the low to the very high cycle regime publication-title: Procedia Engineering – volume: 23 start-page: 143 year: 2001 end-page: 151 ident: bib14 article-title: How and why the fatigue S–N curve does not approach a horizontal asymptote publication-title: Int. J. Fatigue – volume: 8 start-page: 111 year: 2018 ident: bib34 article-title: Study of relation between shot peening parameters and fatigue fracture surface character of an AW 7075 aluminium alloy publication-title: Metals – volume: 34 start-page: 549 year: 1976 end-page: 563 ident: bib5 article-title: Vacancy dipoles in fatigued copper publication-title: Philos. Mag. – volume: 32 start-page: 247 year: 2010 end-page: 255 ident: bib22 article-title: Observations of fatigue crack initiation in 7075-T651 publication-title: Int. J. Fatigue – volume: 6 start-page: 79 year: 2016 ident: bib1 article-title: Effect of heat treatment on the in-plane anisotropy of as-rolled 7050 aluminum alloy publication-title: Metals – volume: 74 start-page: 246 year: 2014 ident: 10.1016/j.msea.2020.138922_bib33 article-title: Fatigue life of AW 7075 aluminium alloy after severe shot peening treatment with different intensities publication-title: Procedia Engineering doi: 10.1016/j.proeng.2014.06.257 – volume: 65 start-page: 18 year: 2014 ident: 10.1016/j.msea.2020.138922_bib9 article-title: Fatigue crack initiation – the role of point defects publication-title: Int. J. Fatigue doi: 10.1016/j.ijfatigue.2013.10.016 – volume: 18 start-page: 785 issue: 7 year: 1970 ident: 10.1016/j.msea.2020.138922_bib27 article-title: Mechanical properties of age-hardened titanium-aluminum alloys publication-title: Acta Metall. doi: 10.1016/0001-6160(70)90043-X – volume: 32 start-page: 248 year: 2013 ident: 10.1016/j.msea.2020.138922_bib32 article-title: Environmental effect on the fatigue performance of bare and oxide coated 7075-T6 alloy publication-title: Eng. Fail. Anal. doi: 10.1016/j.engfailanal.2013.03.020 – year: 2010 ident: 10.1016/j.msea.2020.138922_bib28 – volume: 93 start-page: 3315 year: 2017 ident: 10.1016/j.msea.2020.138922_bib30 article-title: Shot peening as a pre-treatment to anodic oxidation coating process of AW 6082 aluminum for fatigue life improvement publication-title: Int. J. Adv. Manuf. Technol. doi: 10.1007/s00170-017-0776-1 – volume: 34 start-page: 549 issue: 4 year: 1976 ident: 10.1016/j.msea.2020.138922_bib5 article-title: Vacancy dipoles in fatigued copper publication-title: Philos. Mag. doi: 10.1080/14786437608223793 – volume: 896 year: 2017 ident: 10.1016/j.msea.2020.138922_bib19 article-title: Influences on the formability and mechanical properties of 7000-aluminum alloys in hot and warm forming publication-title: J. Phys. Conf. Ser. doi: 10.1088/1742-6596/896/1/012004 – volume: 9 start-page: 171 issue: 2 year: 1973 ident: 10.1016/j.msea.2020.138922_bib23 article-title: The role of inclusions in fatigue crack initiation in an aluminum alloy publication-title: Int. J. Fract. doi: 10.1007/BF00041859 – volume: 13 start-page: 761 year: 1982 ident: 10.1016/j.msea.2020.138922_bib18 article-title: Calorimetric studies of precipitation and dissolution kinetics in aluminum alloys 2219 and 7075 publication-title: Metall. Trans.A doi: 10.1007/BF02642389 – volume: 32 start-page: 247 issue: 2 year: 2010 ident: 10.1016/j.msea.2020.138922_bib22 article-title: Observations of fatigue crack initiation in 7075-T651 publication-title: Int. J. Fatigue doi: 10.1016/j.ijfatigue.2009.06.003 – year: 2006 ident: 10.1016/j.msea.2020.138922_bib3 – volume: 25 start-page: 1101 issue: 9–11 year: 2003 ident: 10.1016/j.msea.2020.138922_bib15 article-title: An understanding of very high cycle fatigue of metals publication-title: Int. J. Fatigue doi: 10.1016/S0142-1123(03)00147-6 – volume: 23 start-page: 143 issue: Supplement 1 year: 2001 ident: 10.1016/j.msea.2020.138922_bib14 article-title: How and why the fatigue S–N curve does not approach a horizontal asymptote publication-title: Int. J. Fatigue doi: 10.1016/S0142-1123(01)00123-2 – volume: 8 start-page: 111 year: 2018 ident: 10.1016/j.msea.2020.138922_bib34 article-title: Study of relation between shot peening parameters and fatigue fracture surface character of an AW 7075 aluminium alloy publication-title: Metals doi: 10.3390/met8020111 – volume: vol. 1 start-page: 427 year: 1973 ident: 10.1016/j.msea.2020.138922_bib26 article-title: Microstructure and fatigue behavior of Al-alloys – start-page: 367 year: 2012 ident: 10.1016/j.msea.2020.138922_bib4 article-title: An understanding of crack growth in VHCF from an internal inclusion in high strength steel – volume: 6 start-page: 79 year: 2016 ident: 10.1016/j.msea.2020.138922_bib1 article-title: Effect of heat treatment on the in-plane anisotropy of as-rolled 7050 aluminum alloy publication-title: Metals doi: 10.3390/met6040079 – volume: 28 start-page: 1501 issue: 11 year: 2006 ident: 10.1016/j.msea.2020.138922_bib2 article-title: Specific features and mechanisms of fatigue in the ultrahigh-cycle regime publication-title: Int. J. Fatigue doi: 10.1016/j.ijfatigue.2005.05.018 – volume: 55 start-page: 636 year: 2013 ident: 10.1016/j.msea.2020.138922_bib25 article-title: Damage mechanisms and fatigue lives: from the low to the very high cycle regime publication-title: Procedia Engineering doi: 10.1016/j.proeng.2013.03.307 – volume: 468–470 start-page: 201 year: 2007 ident: 10.1016/j.msea.2020.138922_bib20 article-title: The influence of soft, precipitate-free zones at grain boundaries in Ti and Al alloys on their fatigue and fracture behavior publication-title: Mater. Sci. Eng. A doi: 10.1016/j.msea.2006.07.168 – volume: 43 start-page: 3813 issue: 10 year: 1995 ident: 10.1016/j.msea.2020.138922_bib6 article-title: Fatigue damage in aluminium single crystals. I. On the surface containing the slip Burgers vector publication-title: Acta Metall. Mater. doi: 10.1016/0956-7151(95)90165-5 – volume: 8 start-page: 1185 year: 1977 ident: 10.1016/j.msea.2020.138922_bib17 article-title: Calorimetric studies of 7000 series aluminum alloys: II. Comparison of 7075, 7050 and RX720 alloys publication-title: Metall. Trans.A doi: 10.1007/BF02667404 – volume: 114 start-page: 197 year: 1989 ident: 10.1016/j.msea.2020.138922_bib16 article-title: Correlation between microstructure and calorimetric behavior of aluminum alloy 7075 and AlZnMg alloys in various tempers publication-title: Mater. Sci. Eng. A doi: 10.1016/0921-5093(89)90859-9 – volume: 308 start-page: 143 issue: 1–2 year: 2001 ident: 10.1016/j.msea.2020.138922_bib12 article-title: Influence of loading frequency on high cycle fatigue properties of b.c.c. and h.c.p. metals publication-title: Mater. Sci. Eng. A doi: 10.1016/S0921-5093(00)01978-X – volume: 596 start-page: 15 year: 2014 ident: 10.1016/j.msea.2020.138922_bib8 article-title: Mechanisms of extrusion and intrusion formation in fatigued crystalline materials publication-title: Mater. Sci. Eng. A doi: 10.1016/j.msea.2013.12.005 – volume: 44 start-page: 405 year: 1981 ident: 10.1016/j.msea.2020.138922_bib10 article-title: A model of extrusions and intrusions in fatigued metals I. Point-defect production and the growth of extrusions publication-title: Philos. Mag. A doi: 10.1080/01418618108239541 – start-page: 707 year: 1979 ident: 10.1016/j.msea.2020.138922_bib11 article-title: Micromechanics theory of fatigue crack initiation applied to time-dependent fatigue – volume: 202 start-page: 5190 issue: 21 year: 2008 ident: 10.1016/j.msea.2020.138922_bib31 article-title: Effect of anodic oxidation on fatigue performance of 7075-T6 alloy publication-title: Surf. Coat. Technol. doi: 10.1016/j.surfcoat.2008.06.049 – year: 1991 ident: 10.1016/j.msea.2020.138922_bib7 – volume: 26 start-page: 940 year: 1991 ident: 10.1016/j.msea.2020.138922_bib21 article-title: The presence and consequences of precipitatefree zones in an aluminium-copper-lithium alloy publication-title: J. Mater. Sci. doi: 10.1007/BF00576770 – volume: 16 year: 2008 ident: 10.1016/j.msea.2020.138922_bib24 article-title: A geometric approach to modeling microstructurally small fatigue crack formation: I. Probabilistic simulation of constituent particle cracking in AA 7075-T651 publication-title: Model. Simul. Mater. Sci. Eng. doi: 10.1088/0965-0393/16/6/065007 – year: 2017 ident: 10.1016/j.msea.2020.138922_bib13 |
| SSID | ssj0001405 |
| Score | 2.414536 |
| Snippet | Advanced electron microscopy methods were used with the aim to explain the differences in the response of strengthened AW 7075 – T6511 aluminum alloy to... |
| SourceID | proquest crossref elsevier |
| SourceType | Aggregation Database Enrichment Source Index Database Publisher |
| StartPage | 138922 |
| SubjectTerms | Aluminum alloys Aluminum base alloys AW7075 Crack initiation Crack propagation Cyclic loads Dislocation density Fatigue Fatigue crack initiation Fatigue damage Fatigue failure Fracture mechanics High cycle fatigue Metal fatigue Ultra-high cycle fatigue |
| Title | Fatigue behavior of AW7075 aluminum alloy in ultra-high cycle fatigue region |
| URI | https://dx.doi.org/10.1016/j.msea.2020.138922 https://www.proquest.com/docview/2579140872 |
| Volume | 774 |
| WOSCitedRecordID | wos000514747200013&url=https%3A%2F%2Fcvtisr.summon.serialssolutions.com%2F%23%21%2Fsearch%3Fho%3Df%26include.ft.matches%3Dt%26l%3Dnull%26q%3D |
| hasFullText | 1 |
| inHoldings | 1 |
| isFullTextHit | |
| isPrint | |
| journalDatabaseRights | – providerCode: PRVESC databaseName: Elsevier SD Freedom Collection Journals 2021 customDbUrl: eissn: 1873-4936 dateEnd: 99991231 omitProxy: false ssIdentifier: ssj0001405 issn: 0921-5093 databaseCode: AIEXJ dateStart: 19950101 isFulltext: true titleUrlDefault: https://www.sciencedirect.com providerName: Elsevier |
| link | http://cvtisr.summon.serialssolutions.com/2.0.0/link/0/eLvHCXMwtV3db9MwELfKxgM8ID7FYCA_wFOUKI2T2H4sY9OGqgmJAn2LnNRBHW1atV01_jf-OO78kUydmACJl7Ry_BH5fj7fnX13hLypMyXiLE7DlOs4hP04DUVZ9sNMaa6ZFJNYGEfhIT8_F-Ox_Njr_fS-MNsZbxpxdSWX_5XUUAbERtfZvyB32ykUwH8gOjyB7PD8I8KfwO-3S9064BtZ8yuHTTtQwImmePUdT9uNw9_lbLNSIcYsDqof0FFQu9aYsMFRzOd7Uhv7-YF3BULU6C6eYRQM7L0xjEhronnM2yZoeFii3X-FAVyx2hxvAq5dXe3iFRinBb-ZIqqmzWaxNYf5fdN31B09GTlYvrM-bWfti9Hq7VEG1b8bG_CwLT9drBrT0XvD_79E1-0doNxi9hXWGeFuOOJYa2YC-IptssVIW14uOAtTaeOreGbPbU6gGxuHtWFcRHNAXYTDRniCa12mdwJyf8LBcKwEGCRqmHfIfsIzCTx1f3B2PP7QSgKgvJortP7jnNOWvV-4O9LvBKMdEcHIPaOH5IFTWOjAAu0R6enmMbl_LYzlEzJ0kKMecnRRUws56iFHDeTotKEd5KiBHHWQoxZyT8nnk-PR0WnosnSEFUvEJlRlnJRKs2yS1axOSpkynQs5yYWa6H6ZaDzL1hVnOVcZBvyVKtegJEtRZYnQjD0je82i0c8J1aCs8DKp61SKtK6YKGsWVywu-SSvhVIHpO-nqKhcCHvMpDIr_F3FiwKntcBpLey0HpCgbbO0AVxurZ35mS_cYrKiZQFAubXdoSdT4XjBuoDdUAIEBE9e_GO3L8m9bgkckj1YlPoVuVttN9P16rWD2y_u6K-B |
| linkProvider | Elsevier |
| openUrl | ctx_ver=Z39.88-2004&ctx_enc=info%3Aofi%2Fenc%3AUTF-8&rfr_id=info%3Asid%2Fsummon.serialssolutions.com&rft_val_fmt=info%3Aofi%2Ffmt%3Akev%3Amtx%3Ajournal&rft.genre=article&rft.atitle=Fatigue+behavior+of+AW7075+aluminum+alloy+in+ultra-high+cycle+fatigue+region&rft.jtitle=Materials+science+%26+engineering.+A%2C+Structural+materials+%3A+properties%2C+microstructure+and+processing&rft.au=Fintov%C3%A1%2C+S.&rft.au=Kub%C4%9Bna%2C+I.&rft.au=Tr%C5%A1ko%2C+L.&rft.au=Horn%C3%ADk%2C+V.&rft.date=2020-02-13&rft.pub=Elsevier+B.V&rft.issn=0921-5093&rft.eissn=1873-4936&rft.volume=774&rft_id=info:doi/10.1016%2Fj.msea.2020.138922&rft.externalDocID=S0921509320300149 |
| thumbnail_l | http://covers-cdn.summon.serialssolutions.com/index.aspx?isbn=/lc.gif&issn=0921-5093&client=summon |
| thumbnail_m | http://covers-cdn.summon.serialssolutions.com/index.aspx?isbn=/mc.gif&issn=0921-5093&client=summon |
| thumbnail_s | http://covers-cdn.summon.serialssolutions.com/index.aspx?isbn=/sc.gif&issn=0921-5093&client=summon |